Metal Density Chart
Density of common metals
Typical values at room temperature. Alloys and castings vary, so use your supplier's figure when you have one. Scroll the table sideways on a phone.
| Metal | kg/m³ | g/cm³ | lb/in³ | lb/ft³ |
|---|---|---|---|---|
| Carbon steel | 7,850 | 7.85 | 0.2836 | 490.1 |
| Stainless steel 304 | 8,000 | 8.00 | 0.2890 | 499.4 |
| Stainless steel 316 | 8,000 | 8.00 | 0.2890 | 499.4 |
| Aluminum (pure) | 2,700 | 2.70 | 0.0975 | 168.6 |
| Aluminum 1100 | 2,710 | 2.71 | 0.0979 | 169.2 |
| Aluminum 3003 | 2,730 | 2.73 | 0.0986 | 170.4 |
| Aluminum 5052 | 2,680 | 2.68 | 0.0968 | 167.3 |
| Aluminum 6061 | 2,700 | 2.70 | 0.0975 | 168.6 |
| Copper (pure) | 8,960 | 8.96 | 0.3237 | 559.4 |
| Brass (yellow, typical) | 8,500 | 8.50 | 0.3071 | 530.6 |
| Bronze (tin bronze, typical) | 8,800 | 8.80 | 0.3179 | 549.4 |
| Cast iron (gray, typical) | 7,200 | 7.20 | 0.2601 | 449.5 |
| Zinc | 7,140 | 7.14 | 0.2579 | 445.7 |
| Lead | 11,340 | 11.34 | 0.4097 | 707.9 |
| Titanium (pure) | 4,510 | 4.51 | 0.1629 | 281.6 |
| Nickel | 8,900 | 8.90 | 0.3215 | 555.6 |
| Tin | 7,290 | 7.29 | 0.2634 | 455.1 |
Weight per area and comparison with steel
How much one square metre of 1 mm sheet and one square foot of 1 inch plate weigh in each metal, and how heavy the metal is compared with carbon steel.
| Metal | 1 mm sheet (kg/m²) | 1 in plate (lb/ft²) | Ratio to steel |
|---|---|---|---|
| Carbon steel | 7.85 | 40.84 | 1.000 |
| Stainless steel 304 | 8.00 | 41.62 | 1.019 |
| Stainless steel 316 | 8.00 | 41.62 | 1.019 |
| Aluminum (pure) | 2.70 | 14.05 | 0.344 |
| Aluminum 1100 | 2.71 | 14.10 | 0.345 |
| Aluminum 3003 | 2.73 | 14.20 | 0.348 |
| Aluminum 5052 | 2.68 | 13.94 | 0.341 |
| Aluminum 6061 | 2.70 | 14.05 | 0.344 |
| Copper (pure) | 8.96 | 46.61 | 1.141 |
| Brass (yellow, typical) | 8.50 | 44.22 | 1.083 |
| Bronze (tin bronze, typical) | 8.80 | 45.78 | 1.121 |
| Cast iron (gray, typical) | 7.20 | 37.46 | 0.917 |
| Zinc | 7.14 | 37.14 | 0.910 |
| Lead | 11.34 | 58.99 | 1.445 |
| Titanium (pure) | 4.51 | 23.46 | 0.575 |
| Nickel | 8.90 | 46.30 | 1.134 |
| Tin | 7.29 | 37.92 | 0.929 |
About this metal density chart
Typical densities of steel, stainless steel, aluminum and other common metals, in metric and imperial units side by side.
Density is the mass of a metal per unit of volume, and it is the one number you need to turn a size into a weight. This chart collects typical densities for the metals that fabricators, machinists and buyers handle most: carbon and stainless steel, pure aluminum and four common aluminum alloys, copper, brass, bronze, cast iron, zinc, lead, titanium, nickel and tin.
Every density is shown four ways. Kilograms per cubic metre (kg/m³) and grams per cubic centimetre (g/cm³) are the metric units used on mill certificates. Pounds per cubic inch (lb/in³) and pounds per cubic foot (lb/ft³) are the units most US shop formulas use. The values come from standard engineering references such as the ASM handbooks, MatWeb and the Engineering ToolBox.
How to use density to find weight
Weight = volume × density. Work out the volume of the part in the same unit system as the density, then multiply.
Metric formula
Weight (kg) = Volume (m³) × Density (kg/m³)
To convert, g/cm³ = kg/m³ ÷ 1,000. So steel at 7,850 kg/m³ is 7.85 g/cm³.
Imperial formula
Weight (lb) = Volume (in³) × Density (lb/in³)
To convert from metric, lb/in³ = kg/m³ × 0.00003613 and lb/ft³ = kg/m³ × 0.06243. Both factors come from 1 inch = 25.4 mm and 1 lb = 0.45359237 kg.
Worked example 1: metric
A 6061 aluminum square bar is 50 × 50 mm and 1 m long. Volume = 0.05 × 0.05 × 1 = 0.0025 m³. Weight = 0.0025 × 2,700 = 6.75 kg. The same bar in carbon steel would weigh 0.0025 × 7,850 = 19.63 kg.
Worked example 2: imperial
A copper bus bar is 1/4 in thick, 4 in wide and 120 in long. Volume = 0.25 × 4 × 120 = 120 in³. Weight = 120 × 0.3237 = 38.84 lb.
Densities used by our calculators
The calculators on this site have three built-in materials: carbon steel at 7,850 kg/m³, stainless steel at 8,000 kg/m³ and aluminum at 2,700 kg/m³. For any other metal in this chart, choose Custom and type its kg/m³ value into the density box. The plate and sheet weight calculator and the steel coil calculator both accept a custom density.
Why published densities differ
Pure metals have a well-defined density, so copper, zinc, lead, nickel, tin and titanium differ only slightly between sources. Alloys depend on what is added: 5052 aluminum contains magnesium, which is lighter than aluminum, so it is a little lighter than pure aluminum, while 3003 contains manganese and is a little heavier.
Brass and bronze are families rather than single materials. Brass is copper and zinc and typically falls between about 8,400 and 8,700 kg/m³ depending on the zinc content. Bronze ranges more widely, from about 7,400 kg/m³ for some aluminum bronzes to about 8,900 kg/m³ for tin bronzes. Gray cast iron ranges from about 6,950 to 7,350 kg/m³ because of its graphite content. Carbon steel is usually taken as 7,850 kg/m³, and stainless grades 304 and 316 are quoted from about 7,900 to 8,000 kg/m³.
Galvanized steel has the same base density as carbon steel; the zinc coating adds a small extra weight per square foot that depends on the coating class.
Temperature also matters a little. Metals expand as they warm up, so their density drops slightly, but the change between a cold yard and a warm shop is far smaller than the difference between two alloys. For weight estimates you can ignore it.
Comparing metals by weight
The ratio column in the second table tells you how heavy a part would be in another metal, compared with the same part in carbon steel. A bracket that weighs 10 kg in steel would weigh about 3.4 kg in 6061 aluminum, about 5.7 kg in titanium and about 11.4 kg in copper. This is a quick way to judge weight savings before you redesign a part, or to check whether a part on a scale is really the metal it is claimed to be.
Frequently asked questions
What is the density of steel?
Carbon steel is normally taken as 7,850 kg/m3, which is 7.85 g/cm3, 0.2836 lb/in3 or about 490 lb/ft3. Real grades vary by around one percent.
What is the density of stainless steel 304 and 316?
Both are typically given as about 8,000 kg/m3, or 0.289 lb/in3. Some sources list 304 at 7,900 to 7,930 kg/m3 and 316 at 7,980 to 8,000 kg/m3.
What is the density of aluminum?
Pure aluminum is about 2,700 kg/m3, or 0.0975 lb/in3. Common alloys are close to that: 6061 is about 2,700, 1100 about 2,710, 3003 about 2,730 and 5052 about 2,680 kg/m3.
How do I convert kg/m3 to lb/in3?
Multiply the kg/m3 value by 0.00003613. For example, 7,850 kg/m3 times 0.00003613 is about 0.2836 lb/in3. To get lb/ft3 instead, multiply by 0.06243.
Which metal in this chart is the heaviest?
Lead is the densest metal in this chart at about 11,340 kg/m3, about 1.44 times as heavy as carbon steel. Aluminum is the lightest at about 2,700 kg/m3, about one third of steel.
Turn a density into a weight with the plate and sheet weight calculator, or see the steel plate weight chart.