Advertisement

Steel Plate Weight Chart

Plate weight in pounds

Carbon steel at 7,850 kg/m³ (0.2836 lb/in³). The sheet columns are the full plate weight in lb. Scroll the table sideways on a phone.

Thickness (in)Decimal (in)mmlb/ft²kg/m²4x8 ft (lb)4x10 ft (lb)5x10 ft (lb)5x20 ft (lb)8x20 ft (lb)
10 gauge0.13453.425.4926.82175.8219.7274.6549.3878.8
3/160.18754.767.6637.39245.0306.3382.9765.71,225.1
1/40.25006.3510.2149.85326.7408.4510.51,021.01,633.5
5/160.31257.9412.7662.31408.4510.5638.11,276.22,041.9
3/80.37509.5215.3174.77490.1612.6765.71,531.42,450.3
1/20.500012.7020.4299.69653.4816.81,021.02,041.93,267.1
5/80.625015.8825.52124.62816.81,021.01,276.22,552.44,083.8
3/40.750019.0530.63149.54980.11,225.11,531.43,062.94,900.6
7/80.875022.2235.73174.471,143.51,429.31,786.73,573.45,717.4
11.000025.4040.84199.391,306.81,633.52,041.94,083.86,534.1
1-1/41.250031.7551.05249.241,633.52,041.92,552.45,104.88,167.7
1-1/21.500038.1061.26299.081,960.22,450.33,062.96,125.79,801.2
1-3/41.750044.4571.47348.932,286.92,858.73,573.47,146.711,434.7
22.000050.8081.68398.782,613.73,267.14,083.88,167.713,068.3

Plate weight in kilograms

The same plates, weighed in kg.

Thickness (in)4x8 ft (kg)4x10 ft (kg)5x10 ft (kg)5x20 ft (kg)8x20 ft (kg)
10 gauge79.799.7124.6249.1398.6
3/16111.1138.9173.7347.3555.7
1/4148.2185.2231.5463.1741.0
5/16185.2231.5289.4578.9926.2
3/8222.3277.9347.3694.61,111.4
1/2296.4370.5463.1926.21,481.9
5/8370.5463.1578.91,157.71,852.4
3/4444.6555.7694.61,389.32,222.9
7/8518.7648.3810.41,620.82,593.4
1592.8741.0926.21,852.42,963.8
1-1/4741.0926.21,157.72,315.53,704.8
1-1/2889.11,111.41,389.32,778.64,445.7
1-3/41,037.31,296.71,620.83,241.75,186.7
21,185.51,481.91,852.43,704.85,927.7

Need a size that is not listed? Enter it in the plate and sheet weight calculator.

Advertisement

About this steel plate weight chart

Weight of carbon steel plate from 10 gauge to 2 inch thick, per square foot, per square metre and for the common full-plate sizes.

This chart lists the weight of flat carbon steel plate for fourteen common thicknesses, from 10 gauge sheet up to 2 inch plate. For each thickness you get the weight of one square foot, one square metre, and five full plate sizes that service centers stock: 4x8, 4x10, 5x10, 5x20 and 8x20 ft. It is meant for quick lookups when you quote a job, plan a lift, load a truck or check a delivery ticket.

All values use carbon steel at 7,850 kg/m³, the figure most US and European suppliers use for mild steel such as A36. Sizes are nominal, so a 4x8 plate is 48 × 96 in and a 1/4 inch plate is 0.25 in thick. For stainless steel or aluminum, use the factor in the density table below.

How to calculate steel plate weight

A plate is a flat block, so its weight is length × width × thickness × density. The chart simply runs that formula for every row and column.

Metric formula

Weight (kg) = Length (m) × Width (m) × Thickness (mm) × 7.85

The 7.85 is the steel density of 7,850 kg/m³ divided by 1,000, because the thickness is in millimetres. It means every square metre of steel weighs 7.85 kg for each millimetre of thickness.

Imperial formula

Weight (lb) = Length (ft) × Width (ft) × Thickness (in) × 40.84

The 40.84 is the weight in pounds of one square foot of steel that is one inch thick. Multiply it by the thickness to get the lb/ft² column, then by the plate area to get a full plate.

Worked example 1: metric

A plate is 3 m long, 1.5 m wide and 10 mm thick. The area is 3 × 1.5 = 4.5 m². Weight = 4.5 × 10 × 7.85 = 353.25 kg, which is about 778.8 lb.

Worked example 2: imperial

A 5x10 ft plate is 3/8 inch thick. The area is 5 × 10 = 50 ft², and 3/8 inch steel weighs 0.375 × 40.84 = 15.31 lb/ft². Weight = 50 × 15.31 = 765.7 lb, which matches the 5x10 column of the chart and is about 347.3 kg.

Density and factors for other metals

The chart is for carbon steel. Because weight goes up in step with density, you can convert any value in the chart to another metal by multiplying it by the factor below. These are typical densities; grades and suppliers differ slightly.

Materialkg/m³lb/in³lb/ft² per inchMultiply chart by
Carbon steel7,8500.283640.841.000
Stainless steel8,0000.289041.621.019
Aluminum2,7000.097514.050.344

For example, a 4x8 sheet of 1/4 inch aluminum weighs about 326.7 × 0.344 = 112.4 lb. The metal density chart lists more metals and alloys.

Tips for reading the chart

Plate is often rolled a little over its nominal thickness, so a real plate can weigh slightly more than the chart says. Mill plate may also be ordered with extra width or length for trimming. Holes, cut-outs and bevels reduce the weight, so subtract their area if the part is heavily cut.

The 10 gauge row uses the standard steel gauge thickness of 0.1345 in. Galvanized and stainless sheet use slightly different thicknesses for the same gauge number; the sheet metal gauge chart lists them.

To weigh several plates, multiply the single-plate value by the number of pieces. Ten 4x8 sheets of 3/16 inch plate weigh about 10 × 245.0 = 2,450 lb, a useful number when you check a forklift or trailer limit.

Frequently asked questions

How much does a 4x8 sheet of 1/4 inch steel plate weigh?

A 4 ft by 8 ft plate of 1/4 inch carbon steel weighs about 326.7 lb, or 148.2 kg. It is 32 square feet at 10.21 lb per square foot.

How much does a 5x10 sheet of 1/2 inch steel weigh?

A 5 ft by 10 ft plate of 1/2 inch carbon steel weighs about 1,021 lb, or 463.1 kg. It is 50 square feet at 20.42 lb per square foot.

What is the weight of steel plate per square foot?

Carbon steel plate weighs about 40.84 lb per square foot for each inch of thickness. Multiply 40.84 by the thickness in inches, so 3/4 inch plate weighs about 30.63 lb per square foot and 2 inch plate about 81.68 lb per square foot.

How much does 10 gauge steel weigh per square foot?

Standard 10 gauge steel is 0.1345 inch thick and weighs about 5.49 lb per square foot. A 4x8 sheet of 10 gauge weighs about 175.8 lb.

Can I use this chart for stainless steel or aluminum plate?

Yes, by multiplying the chart value by a density factor. Use about 1.019 for stainless steel at 8,000 kg/m³ and about 0.344 for aluminum at 2,700 kg/m³.

Why does a real plate weigh more or less than the chart?

The chart uses nominal sizes and a standard density. Rolling tolerance, extra trim allowance, coatings and grade all change the real weight, so treat the chart as a planning figure and check the mill certificate or scale ticket.

Weigh your own size with the plate and sheet weight calculator, or see the sheet metal gauge chart for thin sheet.

Keep going

More handy tools

Advertisement