Advertisement

Sheet Metal Gauge Chart

Gauge numbers with thickness in inches and millimetres for steel, galvanized, stainless and aluminium sheet. Pick a row to work out the weight of a sheet.

Gauge to thickness

Source: Gauge tables vary slightly between sources and mills, so use these figures for reference and check critical sizes with your supplier.

2Sheet weight

Common:
pcs
Show weight in

Sheet weight

0 kg

Thickness-
Pounds-
Total area-

Live 3D preview

Advertisement

About sheet gauges

A gauge number is a traditional way to describe sheet thickness. The higher the number, the thinner the sheet, and the same gauge number gives a different thickness for different metals.

Sheet weight = Length × Width × Gauge thickness × Density

Which table is which?

Standard steel uses the Manufacturers’ Standard Gauge. Galvanized sheet is a little thicker because the figure includes the zinc coating. Stainless often follows the US Standard Gauge, and aluminium the Brown & Sharpe (AWG) gauge.

Galvanized weights use the steel density, so the zinc coating is counted as steel. Results are estimates for planning; real products vary with grade, tolerances and coatings. Always check against your supplier’s data.

Sheet metal gauge: how it works

This gauge chart converts a sheet metal gauge number into thickness in inches and millimetres for standard steel, galvanized steel, stainless steel and aluminium. You can then pick a row to work out the weight of a sheet. It helps when you are reading a drawing that says 14 gauge, comparing quotes, or checking that a supplier shipped the thickness you ordered.

A gauge number is a traditional way of naming thickness. The higher the number, the thinner the sheet, and the same number does not mean the same thickness in every metal. Weights on this page use 7,850 kg/m³ for steel and galvanized steel, 8,000 kg/m³ for stainless steel and 2,700 kg/m³ for aluminium.

How to find sheet weight from gauge

Look up the thickness for your gauge and material in the chart, then treat the sheet as a flat block, so the weight is the volume multiplied by the density.

Metric formula

Weight (kg) = Length (m) × Width (m) × Thickness (mm) × Density (kg/m³) ÷ 1,000

For steel this is the thickness in millimetres times 7.85, which gives kg per square metre.

Imperial formula

Weight (lb) = Length (in) × Width (in) × Thickness (in) × 0.2836

The figure 0.2836 is the density of carbon steel in lb/in³. Use 0.2890 for stainless steel and 0.0975 for aluminium. In feet, one square foot of steel one inch thick weighs about 40.84 lb.

Worked example 1: imperial

A standard 4 ft × 8 ft sheet of 16 gauge steel is 0.0598 in thick.

Area = 32 ft². Weight per square foot = 0.0598 × 40.84 = 2.44 lb. Weight = 32 × 2.44 = 78.1 lb, which is about 35.4 kg.

Worked example 2: metric

An aluminium sheet measures 2,000 mm × 1,000 mm and is 14 gauge, which is 0.0641 in or 1.63 mm thick.

Weight per square metre = 1.63 × 2.7 = 4.40 kg. Area = 2 m². Weight = 8.79 kg, which is about 19.4 lb.

Gauge to thickness chart

These are commonly published reference values. Standard steel follows the Manufacturers' Standard Gauge, galvanized is the galvanized sheet gauge, stainless follows the US Standard Gauge and aluminium follows Brown and Sharpe (AWG). A dash means that gauge is not normally listed for that material. The full chart above covers every gauge from 3 to 30.

Thickness in inches

GaugeStandard steelGalvanized steelStainless steelAluminium
80.16440.16810.17190.1285
100.13450.13820.14060.1019
110.11960.12330.12500.0907
120.10460.10840.10940.0808
140.07470.07850.07810.0641
160.05980.06350.06250.0508
180.04780.05160.05000.0403
200.03590.03960.03750.0320
220.02990.03360.03130.0253
240.02390.02760.02500.0201
260.01790.02170.01880.0159
280.01490.01870.01560.0126

Thickness in millimetres

GaugeStandard steelGalvanized steelStainless steelAluminium
84.184.274.373.26
103.423.513.572.59
113.043.133.172.30
122.662.752.782.05
141.901.991.981.63
161.521.611.591.29
181.211.311.271.02
200.911.010.950.81
220.760.850.800.64
240.610.700.640.51
260.450.550.480.40
280.380.470.400.32

Gauge tables vary slightly between sources and mills, and gauge is not a precise standard, so use these figures for reference and confirm the thickness with your supplier before ordering or cutting.

Sheet weight per area by gauge

Multiply the figure for your gauge by the sheet area to get the weight. Galvanized steel is not shown because it uses the same density as standard steel but a slightly greater thickness at each gauge, so read it from the chart or the calculator above.

GaugeSteel lb/ft²Steel kg/m²Stainless lb/ft²Stainless kg/m²Aluminium lb/ft²Aluminium kg/m²
86.7132.787.1534.931.808.81
105.4926.825.8528.571.436.99
114.8823.855.2025.401.276.22
124.2720.864.5522.231.135.54
143.0514.893.2515.870.904.40
162.4411.922.6012.700.713.48
181.959.532.0810.160.572.76
201.477.161.567.620.452.19
221.225.961.306.360.361.74
240.984.771.045.080.281.38
260.733.570.783.820.221.09
280.612.970.653.170.180.86

Example: ten 4 ft × 8 ft sheets of 16 gauge steel weigh about 10 × 32 × 2.44 = 781 lb.

Frequently asked questions

What is the thickness of 16 gauge steel?

Standard 16 gauge sheet steel is 0.0598 inch (1.52 mm). 16 gauge galvanized steel is thicker at 0.0635 inch (1.61 mm), 16 gauge stainless is 0.0625 inch and 16 gauge aluminium is 0.0508 inch.

Why does the same gauge number give different thicknesses?

Gauge is a traditional number, not a unit, and each metal follows its own gauge system. Standard steel uses the Manufacturers' Standard Gauge, aluminium usually follows Brown and Sharpe (AWG) and stainless often follows the US Standard Gauge. Galvanized sheet figures include the zinc coating, so they are slightly thicker than bare steel.

Is sheet metal gauge a precise standard?

No. Gauge tables vary slightly between sources and mills, and thickness tolerances also apply. For anything critical, order by decimal thickness in inches or millimetres and confirm the exact figure with your supplier.

Does a higher gauge number mean thicker metal?

No, the opposite. A higher gauge number means thinner sheet, so 10 gauge is much thicker than 26 gauge. Very heavy material is often sold by plate thickness rather than gauge.

How do I find the weight of a sheet by gauge?

Look up the thickness for your gauge and material, then multiply length by width by thickness by density. For steel, one square foot weighs about 40.84 lb for each inch of thickness, so 16 gauge standard steel is about 2.44 lb per square foot.

Which density is used for galvanized steel weight?

The chart uses 7,850 kg/m³ for both standard and galvanized steel, so the zinc coating is counted as steel. The real weight is very slightly different, so treat the result as a planning estimate and check the supplier's data.

Need a flat plate by decimal thickness? See the plate and sheet weight calculator and the flat bar weight calculator.

Keep going

More handy tools

Advertisement