Advertisement

Aluminum Coil Weight Calculator

1Coil size

Default unit
Show weight in

The default unit sets every box. Tap the unit inside any box to change just that one.

Common:

2Material

kg/m³

Coil weight

0 kg

Pounds-
Metric tonnes-
MaterialAluminum
Coil length Enter thickness to see length

Live 3D preview

OD - ID - Width -
Advertisement

How it’s calculated

Weight = π ÷ 4 × (OD² − ID²) × Width × Density

Length = π × (OD² − ID²) ÷ (4 × Thickness)

  1. Enter your sizes to see the working here.

What the numbers mean

The calculator treats the aluminum coil as a tube of solid metal: ring area between the core and the outside wrap, times the width, times the density.

Aluminum is about one third as heavy as steel, so the same coil size weighs far less.

The coil is treated as fully wound with no gaps (100% fill). Results are estimates for planning; always check against your supplier’s data.

Aluminum coil weight: what this calculator does

Weigh a coil of aluminum sheet or strip from its width, inside diameter and outside diameter. Aluminum at 2,700 kg/m³ is already selected; type your alloy's density if you need a closer figure.

This aluminum coil weight calculator is for anyone who buys, stores, ships or runs coils of aluminum sheet and strip: roll formers, gutter and trim shops, HVAC and truck body builders, and warehouse staff checking an incoming load. Give it the width, the core diameter and the outside diameter, and it returns the coil weight in kilograms, pounds and metric tonnes. Add the strip thickness to see how many metres or feet of material are on the coil.

The material is set to aluminum at 2,700 kg/m³ (0.0975 lb/in³), the usual figure for pure aluminum and for 6061. Most wrought alloys fall between about 2,680 and 2,730 kg/m³, so if you know your alloy you can type its density into the box. The steel and stainless steel buttons are still there if you need to compare.

How to calculate aluminum coil weight

Treat the coil as a thick-walled tube. The area of its end face is the ring between the two diameters, the width turns that area into a volume, and the density turns the volume into a weight.

Metric formula

Weight (kg) = 0.7854 × (OD² − ID²) × Width × 2,700, with OD, ID and width in metres

Imperial formula

Weight (lb) = 0.7854 × (OD² − ID²) × Width × 0.09754, with OD, ID and width in inches

0.7854 is π ÷ 4, and 0.09754 lb/in³ is 2,700 kg/m³ converted to imperial units.

Worked example 1: metric

An aluminum coil is 1,250 mm wide on a 508 mm core, with a 1,500 mm outside diameter. Ring area = 0.7854 × (1.5² − 0.508²) = 1.5645 m². Volume = 1.5645 × 1.25 = 1.9556 m³. Weight = 1.9556 × 2,700 = 5,280 kg, about 11,641 lb. These are the starting values in the calculator above. A 1 mm thick strip would give about 1,564 m of material.

Worked example 2: imperial

An aluminum coil is 48 in wide with a 20 in ID and a 60 in OD. Weight per inch of width = 0.7854 × (60² − 20²) × 0.09754 = 245.2 lb. Weight = 245.2 × 48 = 11,767 lb, about 5,338 kg. If the sheet is 0.032 in thick, the coil holds about 6,545 ft of it.

Aluminum alloy densities

The alloy changes the weight only slightly. The table shows typical densities and what the 1,250 mm wide coil from example 1 would weigh in each.

Alloykg/m³lb/in³Example coil (kg)Example coil (lb)
Pure aluminum2,7000.09755,28011,641
11002,7100.09795,30011,684
30032,7300.09865,33911,770
31052,7200.09835,31911,727
50522,6800.09685,24111,554
60612,7000.09755,28011,641

Between the lightest and heaviest alloys listed, 5052 and 3003, the gap is under 2 percent. For most freight and lifting checks, 2,700 kg/m³ is close enough. Painted or coated coil carries a little extra weight from the paint system, which this calculator does not include.

Aluminum coil weight per inch of width

The table gives pounds per inch of width (PIW) for aluminum at 2,700 kg/m³. Multiply by the width in inches to get the coil weight. Smaller cores such as 16 in are common on narrow trim and gutter coil.

OD (in)ID 16 inID 20 inID 24 in
3049.338.324.8
3679.768.655.2
42115.5104.591.0
48156.9145.9132.4
54203.8192.8179.3
60256.2245.2231.7

Example: a 24 in wide trim coil on a 16 in core with a 30 in OD weighs about 24 × 49.3 = 1,184 lb.

Frequently asked questions

What density should I use for aluminum coil?

Use 2,700 kg/m3 (0.0975 lb/in3) unless you know the alloy. Typical values are 2,710 for 1100, 2,730 for 3003, 2,720 for 3105, 2,680 for 5052 and 2,700 for 6061.

How much does an aluminum coil weigh?

It depends on the width and the two diameters. A 48 inch wide aluminum coil with a 20 inch ID and a 60 inch OD weighs about 11,767 lb, while a 24 inch wide trim coil on a 16 inch core with a 30 inch OD weighs about 1,184 lb.

Is an aluminum coil lighter than a steel coil of the same size?

Yes. Aluminum at 2,700 kg/m3 is about 0.344 times the weight of carbon steel at 7,850 kg/m3, so an aluminum coil weighs roughly one third of a steel coil with the same width and diameters.

How do I work out the length of an aluminum coil?

Length equals pi times (OD squared minus ID squared), divided by 4 times the thickness, with all sizes in the same unit. A coil with a 60 inch OD, a 20 inch ID and 0.032 inch sheet holds about 6,545 feet.

Does the alloy or temper change the coil weight?

The alloy changes it slightly, by up to about 2 percent between common alloys. The temper, such as H14 or O, does not change the density, so it does not change the weight.

See the full steel coil weight chart, or find an outside diameter from a weight with the coil outer diameter calculator.

Keep going

More handy tools

Advertisement